Zinsser B-I-N Aqua
- 500ml
- 1L
- 2.5L
- 5L
- 500ml
- 1L
- 2.5L
- 5L
- Ultimate performance, water-based primer-sealer
- Effectively blocks odours
- Exceptional adhesion to most surfaces without sanding
- For interior and exterior use
- Seals knots and sap streaks
- Touch dry in just 25 minutes, recoatable in 45 minutes
- Trace VOC
- Drying time: 45 mins
- Coverage: 9 m2
- Coats: 1-2
- Coverage: 10 m2
Zinsser B-I-N Aqua is a water-based primer, sealer, stain killer and odour blocker. The high hiding formulation offers exceptional adhesion, without the need for sanding, and is ideal for both interior and exterior use. ZInsser B-I-N Aqua effectively primes. seals, blocks stains and locks in problem odours, while expertly sealing knots and sap streaks.
- Priming : Use as a full-surface primer on wood panels, building boards, doors, frames. PVC, plywood, concrete, glossy paint and varnish, non-ferrous metal such as galvanised metal, copper, aluminium and stainless steel and other paintable surfaces
- Spot-Priming : Zinsser B-I-N Aqua is excellent for spot priming knots, resins and stains. It is also ideal for interior spot priming of water stains
- Sealing : Zinsser B-I-N Aqua penetrates and seals porous surfaces and dries to a smooth finish with excellent hiding properties. It is an excellent primer for enamel and is ideal for wood, new cured plaster, concrete and concrete block, stucco, drywall, joint compound, untreated wallcovering and other porous surfaces
- Stain and Odour Blocking : Zinsser B-I-N Aqua will effectively block stain from water, nicotine, grease, oil, soot, mildew, tannin, crayon and lipstick. It is also acts as an odour barrier and effectively blocks all types of odours including fire damage, smoke. nicotine, mildew, and odour from fireplaces and heaters
Please note : When using the primer on spot-primed areas with a porous surface it may show through if the topcoat has poor coverage. This also applies to many ceiling paints and shiny enamels, it is recommended to only use a topcoat with good coverage.
For the best results, ensure surfaces to be coated are sound, clean and dry, and free from all defective or poorly adhering material such as dirt, grease, paint or adhesives. If needed, clean surface using Zinsser Universal Degreaser and Cleaner, rinse thoroughly and allow surface to dry completely.
- Take special precautions during surface preparation of pre-1960s paint surfaces over wood and metal as they may contain harmful lead
- Remove and treat any mould and mildew on interior surfaces using Zinsser Mould Killer and Remover
- For exterior surfaces treat mould with a exterior mould killer and remover
- Remove any peeling and or unsound coatings. sand any remaining paint film edges smooth
- When priming over stained areas, first attempt to remove as much stain as possible by washing, sanding and scraping
- Allow surface to dry completely before priming
- Substrate moisture content should not exceed 12%. New plaster which is polished or dusty should be sealed first with Zinsser Gardz
- Degrease new galvanised steel with Zinsser Universal Degreaser and Cleaner ensuring all traces of oil and surface contamination are removed
Always do a test area before starting any project to check product suitability and effectiveness. Follow the manufacturer's instructions on the tin at all times.
Only apply at temperatures ranging between 7°C and 32°C with a relative humidity of less than 85%. Do not apply in direct sunlight or if condensation, rain, fog, frost etc, is likely to affect the freshly applied primer coat.
- Shake or stir thoroughly before and periodically during use
- Apply Zinsser B-I-N with a good quality natural or synthetic brush, microfibre roller, applicator pad or spray gun
- Apply 1 full coat to prepared surfaces. A second coat on very porous surfaces or heavy staining may be necessary
- Allow 45 minutes between coats
- Fully cured in 5 - 7 days
Spray gun Guidelines
- Normal use: Thinning is not required, however, if necessary, add no more than 5% clean water. Do not thin if using for stain, knot or odour blocking
- Airless sprayer: Use tip size 0.015 - 0.017 at pressure 1700 - 2200 psi
Dry Time
At normal temperatures Zinsser B-I-N is touch dry in 25 minutes and can be recoated in 45 minutes. Lower temperatures, high humidity, and the addition of tint will prolong the dry and cure time of the product. For knots and stains, allow 2 hours to dry. When sealing water stains, some stains may appear in the primer as it dries, this is normal. Stains will be locked in the primer film and will not bleed into the topcoat.